- Can the TSM-110-01-S-DV-017-TR be used in applications requiring continuous operation across the full -55°C to 125°C temperature range without derating?
- The TSM-110-01-S-DV-017-TR is rated for -55°C to 125°C operation, but thermal cycling and sustained high-temperature exposure can accelerate degradation of the LCP insulation material and the gold-plated mating contacts. In industrial designs, especially those involving repeated thermal stress, evaluate whether active thermal management or derating at extremes is needed. The phosphor bronze contact material maintains mechanical properties across the range, but contact resistance can drift slightly at temperature boundaries, so applications requiring stable impedance should account for this drift during design validation.
- What are the key differences between the TSM-110-01-S-DV-017-TR and equivalent unshrouded 20-position headers from competing manufacturers, and when would shrouding be necessary instead?
- The TSM-110-01-S-DV-017-TR is unshrouded, which reduces cost and board space but eliminates mechanical keying and misalignment protection. Competitors like JST and Molex offer shrouded variants that prevent reversed mating and guide cable insertion. Choose the TSM-110-01-S-DV-017-TR for applications where connector orientation is controlled by PCB layout or housing design. Migrate to a shrouded alternative if your design requires field assembly, high-volume consumer production with low assembly training, or environments where cable pull forces risk accidental displacement.
- How does the cuttable design of the TSM-110-01-S-DV-017-TR affect layout flexibility, and are there constraints on where the connector can be cut?
- The TSM-110-01-S-DV-017-TR features a cuttable header, allowing custom segmentation to match exact pin counts on your PCB. However, cuts must be made between column pairs (perpendicular to the pin rows) to maintain structural integrity and solder pad alignment. Improper cutting can damage the insulation material or misalign the remaining pins. Plan your PCB layout and routing before finalizing cut positions, as rework after cutting is difficult. For prototype iterations, consider ordering full 20-position headers and cutting as needed rather than pre-cutting from the supplier.
- What soldering profile and thermal management are recommended for reliable solder joints with the TSM-110-01-S-DV-017-TR on a high-density PCB?
- The TSM-110-01-S-DV-017-TR uses standard solder termination suitable for reflow soldering. Peak reflow temperature should not exceed 260°C to protect the LCP insulation, which softens above this threshold. For surface-mount assembly, use a ramp-to-peak profile with a preheat temperature of 150–180°C held for 60–120 seconds to minimize thermal shock to the board. On high-density boards with limited thermal mass, consider localized heating or slow reflow rates. Post-reflow inspection under magnification is essential because LCP shrinkage during cooling can create solder bridges on adjacent pins; test for shorts between adjacent contacts before functional testing.
- The TSM-110-01-S-DV-017-TR lists 19 positions loaded out of 20—what is the reason for this configuration, and can a fully loaded 20-position variant be substituted?
- The TSM-110-01-S-DV-017-TR is factory-configured with 19 positions loaded, likely to accommodate specific customer requirements or to prevent a reserved or ground position from being used. Before substituting a fully loaded 20-position variant, verify with Samtec or your supplier whether the 20th position is intentionally omitted for electrical safety, keying, or grounding purposes. Substituting without confirmation could introduce crosstalk, unintended signal coupling, or safety hazards. If you require 20 active positions, explicitly request a TSM-110 variant specifying 20 loaded positions and confirm compatibility with your application.
- How does the 2.54 mm pitch of the TSM-110-01-S-DV-017-TR compare to finer-pitch alternatives, and when is pitch density the limiting factor in connector selection?
- The TSM-110-01-S-DV-017-TR uses standard 2.54 mm (0.100") pitch, a legacy spacing that accommodates hand assembly, large wire gauges, and simplifies PCB routing. Finer-pitch alternatives (1.27 mm, 1.00 mm) reduce board footprint but increase assembly complexity and require tighter manufacturing tolerances. Choose the TSM-110-01-S-DV-017-TR when ruggedness, field repairability, or compatibility with legacy systems is prioritized. Switch to finer pitch only if board space is genuinely constrained and your manufacturing process can reliably achieve smaller tolerances without compromising yield or reliability.
- What is the expected contact mating and post life for the TSM-110-01-S-DV-017-TR in repeated connect/disconnect cycles, and how does this affect field maintenance scenarios?
- The TSM-110-01-S-DV-017-TR does not specify mating cycle life in the datasheet, but unshrouded headers typically tolerate 100–500 mating cycles before contact wear becomes noticeable. The gold-plated mating surface provides corrosion resistance but is thin (0.76 µm), so repeated insertion can eventually expose underlying phosphor bronze. In applications requiring frequent disconnection (test points, reconfigurable modules), use a shrouded header instead, or design the system to minimize disconnect events. For permanent installations, the TSM-110-01-S-DV-017-TR is suitable with minimal lifecycle concerns.
- The TSM-110-01-S-DV-017-TR is RoHS3 compliant—what are the implications for lead-free solder compatibility and wave soldering suitability?
- RoHS3 compliance confirms the TSM-110-01-S-DV-017-TR is lead-free and compatible with lead-free solder alloys (SAC305, SAC305 with silver). However, lead-free solder has a higher melting point (~217°C vs. 183°C for leaded), which increases thermal stress on the LCP insulation during reflow. The connector is rated for reflow but is not recommended for wave soldering due to the thermal profile required and potential LCP warping. If your legacy process uses wave soldering, consult Samtec for thermal simulation or consider hand-soldering critical connections. For new designs, use reflow with controlled thermal profiles as described in the assembly guidelines.
- Can the TSM-110-01-S-DV-017-TR be used in medical, aerospace, or automotive applications, and what additional qualification or testing is required?
- The TSM-110-01-S-DV-017-TR carries a UL94 V-0 flammability rating and MSL1 moisture sensitivity, making it suitable for general industrial use. However, it is not listed as qualified for medical (IEC 60601), aerospace (AS25042), or automotive (AEC-Q200) specifications. Deployment in regulated industries requires full qualification testing, including vibration, thermal cycling, humidity bias, and contact resistance stability. Contact Samtec directly for guidance on design alternatives or custom validation programs if your application requires such certifications.
- How does the unshrouded design and push-pull fastening mechanism of the TSM-110-01-S-DV-017-TR affect pull force and connector retention in high-vibration environments?
- The TSM-110-01-S-DV-017-TR uses a push-pull fastening mechanism that relies on friction and mechanical engagement rather than a latching lever. In high-vibration environments, repeated micro-movements can loosen the connector. The unshrouded design provides no mechanical keys to resist accidental withdrawal. For applications subject to continuous vibration (industrial motors, mobile platforms), secure the connector with cable strain relief, adhesive backing, or a vibration-proof enclosure. Alternatively, migrate to a shrouded, latched variant with a defined release force specification.




